新聞資訊【NEWS】more>>
行業新聞

當前位置:網站首頁 > 新聞資訊 > 行業新聞

  • 外牆保溫闆怎麼樣粘貼
  • 本站編輯:杭州博恩環保科技有限公司發布日期:2019-05-06 09:58 浏覽次數:

外牆保溫闆在生活使用中并不陌生,作為新型的建築材料,外牆保溫闆專指用于建築牆體的一類保溫材料,下面杭州博恩環保科技有限公司就帶我們一起了解一下外牆保溫闆粘貼的注意事項有哪些吧:

  1、外牆保溫闆某一面因包裝、運輸等原因造成微小的缺陷時,則應将這一面作為抹膠面。

  2、将塗抹好膠粘劑的保溫闆緊密地粘貼在牆面上(或插入托架),在粘貼下一塊保溫闆時,應将這塊闆從側面推壓向前一塊闆,并保證保溫闆與保溫闆之間的接縫被壓緊。在牆角托架處,玻璃纖維網格布應延伸至托架的底邊邊緣,多餘部分用刀切除。

  3、保溫闆間高差不得大于1.5㎜(或4㎜/2m),當保溫闆間高差有大于1.5㎜的部位,應在粘膠硬化後做輕柔圓周運動打磨平整。

外牆保溫闆


  4、粘貼保溫闆縫應輕揉,均勻擠壓、擠緊,保溫闆縫應錯開,相鄰外牆保溫闆應齊平,粘結砂漿擠出時用鏟刀必須立即刮掉,使保溫闆與保溫闆之間無“碰頭灰”。

  保溫闆間縫隙不得大于2㎜,保溫闆縫隙大于2㎜時,應用保溫闆條将縫塞滿,保溫闆條不得粘結,更不得用膠粘劑直接填縫。

  以上就是關于外牆保溫闆在粘貼時注意的事項,杭州博恩環保科技有限公司 就是經營外牆保溫闆的,如果你有相關的需要歡迎咨詢我們。


l2-161215141025_180_134[1].jpg

The external wall insulation board is not unfamiliar in the use of life. As a new type of building material, the external wall insulation board specifically refers to a type of insulation material used for building walls. The following Hangzhou Boen Environmental Protection Technology Co., Ltd. will take us to understand the external wall insulation board. What are the points of note for pasting:
When one side of the external wall insulation board causes minor defects due to packaging, transportation, etc., this side should be used as a rubber surface.
2, the coated adhesive insulation plate is closely affixed to the wall(or inserted into the bracket), when pasting the next plate, this plate should be pushed from the side of the forward plate, and ensure that the insulation board and the interface between the plate is pressed. At the corner bracket, the fiberglass mesh cloth should be extended to the bottom edge of the bracket, and the excess parts should be removed with a knife.
3, the difference between the insulation board must not be greater than 1.5 <UNK>(or 4 <UNK> / 2m), when the difference between the insulation board is greater than 1.5 <UNK>, soft circular motion grinding should be done after the adhesive hardens.
External wall insulation board
4, paste the insulation board seams should be gently rubbed, evenly squeezed, squeeze, insulation board seams should be staggered, adjacent external wall insulation board should be flat, glue mortar extrusion with a shovel knife must be immediately scraped off, so that the insulation board and the insulation board There is no "meeting ash."
The gap between the insulation board must not be greater than 2 <UNK>, when the gap between the insulation board is greater than 2 <UNK>, the insulation board is applied to fill the seam, the insulation board is not bonded, and the adhesive is not used to fill the seam directly.
The above is about the external insulation board in the pasting matters, Hangzhou boan environmental protection technology Co., Ltd. is operating external insulation board, if you have relevant needs welcome to consult us.

http://m.juhua752585.cn|http://wap.juhua752585.cn|http://www.juhua752585.cn||http://juhua752585.cn